How much does HVAC cost in Fort Worth?
By Our research team · Last verified · Methodology
Most Fort Worth homeowners pay $3,800–$8,550 to replace a central AC sized at 3 tons on ducts you already have. $5,900 is typical, and a single-zone 12,000 BTU mini-split is $2,400–$5,400.
How we get this data- Typical
- $5,900
- Low end
- $2,850
- High end
- $12,850
Want an exact price for your job?
Tell us the job. Casey checks it by text, then up to 2 local HVAC contractors send you a real quote. Free, no obligation.
Get my fair quote →The typical Fort Worth price is $5,900, 5% below the US typical of $6,200.
Fort Worth's price band
Fort Worth is pricier than 65% of the 195 US metros we price for HVAC work.
Replacing a 3-ton central AC in Fort Worth costs $3,800–$8,550 on existing ducts, with $5,900 typical. A 3-ton heat pump runs $5,300–$12,100, a gas furnace $2,700–$7,750, and a single-zone mini-split $2,400–$5,400.
Fort Worth shares the DFW pattern: a long cooling season and spring hail that can wreck condenser coils. Under the federal Southeast standard, a new split central AC under 45,000 BTU must be at least 14.3 SEER2.
Prices on this page are installed: equipment, labor, removal of the old unit and startup. A permit ($95–$240), a new line set ($190–$620) or duct repairs may be extra, so ask. Labor is usually 40–60% of the bill.
Comparing cities, or after the US-wide picture? See the national guide: HVAC cost in the USA.
$3,800–$8,550 to replace a 3-ton central AC on existing ducts in Fort Worth, installed — $5,900 typical. A heat pump runs $5,300–$12,100, a gas furnace $2,700–$7,750, and AC + furnace together $6,300–$15,450. Verified November 2026. Get free Fort Worth quotes →
- 3-ton central AC on existing ducts: $3,800–$8,550 ($5,900 typical)
- Heat pump, 3-ton: $5,300–$12,100; gas furnace: $2,700–$7,750
- AC + furnace together: $6,300–$15,450
- Mini-split: $2,400–$5,400 for one 12,000 BTU zone, $7,750–$17,400 for four
- Downtown & Near Southside runs 5–10% above the city average; Westside & Cultural District: standard pricing
Prices verified November 2026 · Cross-referenced against 45+ American pricing sources · See methodology
Installed prices for the Fort Worth metro, re-verified November 2026. Equipment-heavy jobs move less with local labor costs than service calls do.
| Service | Low | Typical | High |
|---|---|---|---|
| Central AC replacement, 3-ton (existing ducts)installed | $3,800installed | $5,900 | $8,550 |
| Central AC + gas furnace, replaced togetherinstalled | $6,300installed | $9,450 | $15,450 |
| Heat pump replacement, 3-ton (existing ducts)installed | $5,300installed | $7,750 | $12,100 |
| Central heat pump, high-efficiency with zoning (3-ton)installed | $9,650installed | $14,000 | $20,300 |
| Gas furnace replacement (80–96% AFUE)installed | $2,700installed | $4,450 | $7,750 |
| Ductless mini-split, 1 zone, 9,000 BTUinstalled | $2,150installed | $3,200 | $4,650 |
| Ductless mini-split, 1 zone, 12,000 BTUinstalled | $2,400installed | $3,750 | $5,400 |
| Ductless mini-split, 1 zone, 18,000 BTUinstalled | $3,100installed | $4,850 | $6,950 |
| Ductless mini-split, 1 zone, 24,000 BTUinstalled | $3,650installed | $6,000 | $8,500 |
| Ductless mini-split, 1 zone, 30,000–36,000 BTUinstalled | $4,650installed | $7,550 | $11,100 |
| Multi-zone mini-split, 2 zonesinstalled | $4,350installed | $6,300 | $9,650 |
| Multi-zone mini-split, 4 zonesinstalled | $7,750installed | $11,600 | $17,400 |
| Like-for-like AC swap: same-size mini-split, existing line setinstalled | $2,200installed | $3,400 | $5,000 |
| Install only: homeowner-supplied mini-split, 1 zonelabor only | $480labor only | $1,050 | $1,900 |
| Evaporative (swamp) cooler, roof-mountedinstalled | $1,250installed | $2,200 | $3,500 |
| Ductwork replacement, whole houseinstalled | $2,400installed | $5,300 | $9,150 |
| AC compressor replacement (out of warranty)per repair | $1,250per repair | $2,050 | $2,900 |
| AC repair, major: refrigerant leak fix + rechargeper repair | $580per repair | $1,250 | $2,400 |
| AC repair, minor: capacitor, contactor or drain lineper repair | $140per repair | $290 | $570 |
| AC tune-upper visit | $70per visit | $100 | $190 |
| Whole-system HVAC tune-up (AC + furnace)per year | $140per year | $220 | $430 |
| Duct cleaning, whole houseper home | $290per home | $430 | $670 |
| Smart thermostat, installedinstalled | $200installed | $290 | $440 |
| Old AC or furnace removal and disposalper unit | $95per unit | $240 | $480 |
Got it as a PDF or photo? Upload up to 3 quotes and compare →
Get free quotes from up to 2 local HVAC contractors in Fort Worth
Free · No obligation · About a minute
- 1The job
- 2Budget
- 3Your details
What do you need a price on?
Tap one to start.
What's your rough budget?
A ballpark is fine. It helps the HVAC contractors who reply.
Where should they text you?
- Max 2 HVAC contractors. No call floods.
- 100% free. No obligation.
- 🔒 Only your matched HVAC contractors see your number.
By continuing, you agree to our Terms and to up to 2 HVAC contractors contacting you by phone or text.
Check your phone
Prices verified November 2026 · Cross-referenced against 45+ American pricing sources · See methodology
Prices cover the Fort Worth metro: the city and its close suburbs. Outlying towns can run a little lower; Downtown & Near Southside runs a little higher.
HVAC prices across Fort Worth
Where you live changes the quote. Downtown & Near Southside costs the most because of access and older buildings; Westside & Cultural District usually comes in at or under the city typical.
Downtown & Near Southside
- Installed
- $4,000–$9,400 installed
- Typical job
- $5,600–$7,450 / 3-ton AC swap
Older homes and mid-rise buildings. A like-for-like condenser swap is routine, but rooftop units and long line runs push quotes toward the top of the range.
Stop Six & East Fort Worth
- Installed
- $3,900–$9,000 installed
- Typical job
- $5,400–$7,100 / 3-ton AC swap
A mix of renovated older homes and newer builds. Ductless mini-splits are common where old houses never had ducts.
Westside & Cultural District
- Installed
- $3,800–$8,550 installed
- Typical job
- $5,300–$6,800 / 3-ton AC swap
Standard pricing for a standard swap: easy access, driveway parking and ducts that are usually in fair shape.
Arlington & the Mid-Cities
- Installed
- $3,800–$9,050 installed
- Typical job
- $5,300–$7,200 / 3-ton AC swap
Bigger homes with garages and attics. Many need 4 to 5 tons or two systems, and attic air handlers take longer to swap than ones in a garage or closet.
Real-world HVAC costs in Fort Worth
Here's what common HVAC jobs cost in Fort Worth in 2026, a 3-ton central AC replacement on existing ducts, installed.
Swap a 3-ton AC on good ducts
Same spot, same size, matched indoor coil, old unit hauled away. Most Fort Worth jobs land near $5,900; a 17+ SEER2 unit adds about $2,000.
Replace the AC and gas furnace together
The usual move when both are 15+ years old. One install, one warranty, a matched system. Typical is $9,450.
Switch from AC + furnace to a heat pump
A 3-ton heat pump on existing ducts, typically $7,750. Keeping the furnace as backup (dual-fuel) runs $6,850–$16,400.
Cool one room with a mini-split
A 12,000 BTU single-zone mini-split for a bedroom, office or addition, typically $3,750. A 9,000 BTU unit for a small room is $2,150–$4,650.
Cool a whole home with no ducts
A 4-zone ductless system, typically $11,600. Adding ducts for central AC instead costs $2,400–$9,150 before the equipment.
How much does HVAC cost in Fort Worth?
A typical 3-ton replacement in Fort Worth is $5,900, inside a normal range of $3,800–$8,550. That price is about 5% below the US typical of $6,200. Most of the difference between quotes is efficiency, brand and how hard the old equipment is to reach.
For homes without ducts, a single-zone mini-split runs $2,400–$5,400 and a 4-zone system $7,750–$17,400. Adding whole-house ducts instead costs $2,400–$9,150 on top of the equipment.
Central AC, heat pump and furnace prices in Fort Worth (2026)
A 3-ton central AC runs $3,800–$8,550, a 3-ton heat pump $5,300–$12,100, and a gas furnace $2,700–$7,750, all installed.
| Line on the quote | Low | Typical | High |
|---|---|---|---|
| Central AC replacement, 3-ton (existing ducts) | $3,800 | $5,900 | $8,550 |
| Heat pump, 3-ton (existing ducts) | $5,300 | $7,750 | $12,100 |
| Gas furnace (80–96% AFUE) | $2,700 | $4,450 | $7,750 |
| Central AC + gas furnace together | $6,300 | $9,450 | $15,450 |
| Mini-split, 1 zone, 12,000 BTU | $2,400 | $3,750 | $5,400 |
| Mini-split, 2 zones | $4,350 | $6,300 | $9,650 |
| Mini-split, 4 zones | $7,750 | $11,600 | $17,400 |
| Ductwork replacement, whole house | $2,400 | $5,300 | $9,150 |
AC or heat pump in Fort Worth? A heat pump costs about $1,850 more than a 3-ton AC at the typical price, but it also replaces your heating. If your furnace is old, compare a heat pump with the $9,450 AC + furnace swap, not with the AC alone.
What moves an HVAC quote in Fort Worth:
- Size: a 2-ton system runs about $4,950 and a 5-ton about $8,300 at the typical price. Ask for a Manual J load calculation.
- Efficiency: the minimum here is 14.3 SEER2; a 17+ SEER2 two-stage unit adds about $2,000.
- Access: attic air handlers, rooftop condensers and tight closets add labor, most often in Downtown & Near Southside.
- Line set and coil: a new line set runs $190–$620, and the indoor coil has to match the new refrigerant.
- Season: spring and fall bring the best prices; a breakdown during a summer heat wave brings the worst.
Ask every Fort Worth contractor for the same things: tonnage, SEER2 rating, model numbers for both the outdoor and indoor units, and whether the permit and line set are included. Compare those, not just the total. Get a quote for your heating and cooling work →
HVAC cost in Fort Worth by home size
About $5,350 for a 2.5-ton AC (1,000–1,600 sq ft), $5,900 for 3 tons (1,600–2,000 sq ft), and $7,300–$8,300 for 4–5 tons in homes over 2,500 sq ft, typical Fort Worth prices on existing ducts.
Worked example: a 2,000 sq ft Fort Worth home with a 16-year-old AC and furnace. Replacing both runs about $9,450; switching to a 3-ton heat pump on the same ducts runs about $7,750; replacing only the AC is $5,900 but leaves an old furnace in place.
Homes over 2,500 sq ft or with two floors often have two systems or zoning. A high-efficiency zoned heat pump runs $9,650–$20,300, and adding zoning to an existing system $1,650–$4,350.
Fort Worth HVAC costs by system type
| System type | Cost | Best for |
|---|---|---|
| Central AC, 3-ton (existing ducts) | $3,800–$8,550 installed | Homes with sound ducts and a furnace or air handler to pair with |
| Ductless mini-split, single zone (9,000–18,000 BTU) | $2,150–$6,950 installed | One room, an addition, or a home with no ducts |
| Multi-zone ductless mini-split (2–4 zones) | $4,350–$17,400 installed | Whole homes with no ducts, room-by-room control |
| Heat pump, 3-ton ducted (heats and cools) | $5,300–$12,100 installed | Mild and hot climates; replacing an AC and electric heat |
| Gas furnace + AC, replaced together | $6,300–$15,450 installed | Cold climates with natural gas and old equipment on both sides |
| Gas furnace only (80–96% AFUE) | $2,700–$7,750 installed | When the AC is newer than the furnace |
| Dual-fuel: heat pump + gas furnace | $6,850–$16,400 installed | Cold climates: electric heat most days, gas on the coldest |
| Cold-climate heat pump, 3-ton ducted | $9,200–$23,200 installed | Northern homes leaving gas, oil or propane |
| Central heat pump, high-efficiency with zoning | $9,650–$20,300 installed | Big or two-story homes with hot and cold rooms |
| Evaporative (swamp) cooler, roof-mounted | $1,250–$3,500 installed | Dry Western climates only |
| Geothermal heat pump (ground loop) | $14,500–$33,800 installed | Large lots and long stays in one home |
| Window or through-the-wall AC | $200–$1,150 installed | Single rooms and renters; cheapest way to cool |
Equipment vs installation: the Fort Worth AC bill
On a typical $5,900 3-ton swap in Fort Worth, the condenser and matched coil are roughly $2,350–$3,550 and the rest is labor, materials, the permit and overhead. Labor usually makes up 40–60% of an AC replacement.
Buying the unit yourself rarely saves much: many contractors won't install customer-supplied equipment, and the ones who do charge $480–$1,900 or more for a mini-split and won't cover the parts. Brand warranties often require a licensed installer.
What's included in a Fort Worth AC replacement (and what costs extra)
A standard replacement quote covers the outdoor unit, a matched indoor coil, refrigerant, connection to your existing ducts and wiring, removal of the old unit, and startup. Common extras:
- Permit and inspection: $95–$240, often built into the quote
- New refrigerant line set: $190–$620 if the old one can't be reused
- New condenser pad: $40–$240
- Electrical panel upgrade: $810–$3,850, mostly when adding a heat pump or more capacity
Ask for the AHRI certificate showing the matched rating of your outdoor and indoor units. It proves the system you paid for is the one that was installed.
Fort Worth's climate
Fort Worth shares the DFW pattern: a long cooling season and spring hail that can wreck condenser coils. Under the federal Southeast standard, a new split central AC under 45,000 BTU must be at least 14.3 SEER2.
System size
Each ton adds equipment cost: about $4,950 for 2 tons and $7,300 for 4 tons at the typical Fort Worth price. A Manual J load calculation often shows a smaller system will do.
Efficiency rating
The federal minimum for a new split AC here is 14.3 SEER2 for units under about 3.75 tons, and 13.8 SEER2 for bigger units. Higher ratings cost more upfront and pay back fastest where AC runs most of the year.
New refrigerants
New systems use A2L refrigerants (R-454B or R-32), so the indoor coil must match the outdoor unit. That's why condenser-only swaps are rare now, and why older R-410A systems cost more to service.
Ducts and access
Leaky or undersized ducts, attic air handlers and rooftop condensers add hours. Whole-house duct replacement runs $2,400–$9,150.
Location: Downtown & Near Southside vs Westside & Cultural District
Downtown & Near Southside jobs cost more because of access, parking and older buildings. Westside & Cultural District quotes usually sit at or a little under the city typical.
Season and urgency
Replacing on your schedule in spring or fall is cheaper than an emergency swap in a heat wave. After-hours repair labor runs $150–$240 an hour.
- Get three quotes for the same system.Same tonnage, same SEER2 rating, model numbers on every quote. Fort Worth quotes for the same 3-ton swap run anywhere from $3,800 to $8,550.
- Replace before it fails.If your system is 12–15+ years old, replace it in spring or fall. Emergency replacements in peak season leave no room to shop around.
- Right-size the system.Ask for a Manual J load calculation. An oversized AC costs more, cycles on and off, and leaves the house clammy.
- Check your utility for rebates.There is no federal tax credit for systems installed in 2026, but many utilities still pay rebates on efficient heat pumps and AC. Check before you sign; most require pre-approval or a listed contractor.
- Do the AC and furnace together if both are old.One install of both runs $6,300–$15,450, less than two separate jobs.
- Keep up with tune-ups.A yearly tune-up at $70–$190 catches weak capacitors and low refrigerant before they kill a compressor ($1,250–$2,900).
Before you pay a deposit to a Fort Worth HVAC contractor, get these in writing:
- Tonnage and how it was sized (a Manual J load calculation)
- Model numbers for the outdoor unit and the indoor coil or air handler
- The matched SEER2 (and HSPF2 for a heat pump) rating
- Whether the line set is new, flushed or reused
- Permit, inspection and removal of the old unit
- Thermostat, pad, disconnect and any electrical work
- Parts and labor warranty terms, and who registers the equipment
- Total price, deposit, and start and finish dates
How much does it cost to replace a central AC in Fort Worth?
$3,800–$8,550 for a 3-ton system on existing ducts, installed, with $5,900 typical in Fort Worth. Higher-efficiency units, attic or rooftop installs and new line sets push it up.
How much does a heat pump cost in Fort Worth?
$5,300–$12,100 for a 3-ton heat pump on existing ducts, about $7,750 typical. A high-efficiency zoned system runs $9,650–$20,300.
How much is a new furnace in Fort Worth?
$2,700–$7,750 for a gas furnace installed, about $4,450 typical. With a new AC at the same time, $6,300–$15,450.
How much does a mini-split cost in Fort Worth?
$2,400–$5,400 for a 12,000 BTU single zone, $4,350–$9,650 for two zones and $7,750–$17,400 for four.
How much is an AC tune-up in Fort Worth?
$70–$190 per visit. A yearly plan for AC and furnace runs $140–$430.
How much does AC repair cost in Fort Worth?
$140–$570 for common fixes like a capacitor or contactor. A refrigerant leak repair with recharge runs $580–$2,400, and a compressor $1,250–$2,900.
What size AC does a Fort Worth home need?
As a rough guide, 2.5 tons covers about 1,000–1,600 sq ft and 3 tons about 1,600–2,000 sq ft, but insulation, windows and climate change that. Ask for a Manual J load calculation instead of matching the old unit.
Is there a tax credit for a new AC or heat pump in Fort Worth?
No federal one for 2026: the 25C credit covered improvements made through December 31, 2025. Utility and state rebates may still apply, so check before you buy.
Do I need a permit to replace an AC in Fort Worth?
Usually, yes. Most US cities and counties require a mechanical permit for an AC or furnace replacement, typically $95–$240, and a licensed contractor normally pulls it.
How much does it cost to add ducts in Fort Worth?
$2,400–$9,150 for whole-house ductwork, before the AC or heat pump. In many older homes a multi-zone mini-split ($7,750–$17,400 for four zones) costs less.
Prices verified November 2026 · Cross-referenced against 45+ American pricing sources · See methodology
Prices for the Fort Worth metro area, November 2026. Outer suburbs may vary.
Get a fair HVAC quote in Fort Worth
Local HVAC contractors · Free quotes · No obligation, no spam.