How much does gas line installation cost in Riverside?
By Our research team · Last verified · Methodology
Most new gas lines to one appliance in Riverside cost $280–$1,400 for a short run of about 10–30 feet from existing pipe, installed and pressure-tested. $610 is the typical bill; hooking a range up to a line that's already there is $120–$420.
How we get this data- Typical
- $610
- Low end
- $140
- High end
- $2,350
Want an exact price for your job?
Tell us the job. Casey checks it by text, then up to 2 local gas line plumbers send you a real quote. Free, no obligation.
Get my fair quote →The typical Riverside price is $610, 6% below the US typical of $650.
Riverside's price band
Riverside is pricier than 59% of the 195 US metros we price for gas line work.
A short new gas line to one appliance costs $280–$1,400 in Riverside, and $610 is typical. Hooking up a range to an existing line is $120–$420, a grill or fire pit line $380–$1,900, and a standby generator line $470–$2,850.
Most Inland Empire homes are slab-built, so new gas runs usually go through the attic or along an outside wall. California requires water heaters to be strapped for earthquakes, and fire-season power shutoffs push demand for generator gas lines in foothill areas.
Gas work needs a licensed plumber or gas fitter, and in most of the US a permit and a pressure test. Prices on this page include the pipe, fittings, a shutoff valve, labor and the test unless the row says otherwise. Budget $50–$340 for the permit in Riverside.
Comparing cities, or after the US-wide picture? See the national guide: Gas line installation cost in the USA.
$280–$1,400 for a short new gas line to one appliance in Riverside, installed — typically $610. Hooking up a range to an existing line is $120–$420, and a 50+ ft run $850–$3,800. Verified November 2026. Get free Riverside quotes →
- Short new gas line to one appliance: $280–$1,400 ($610 typical)
- Range hookup on an existing line $120–$420; dryer hookup $95–$330
- Grill or fire pit line $380–$1,900; standby generator line $470–$2,850
- Leak repair $140–$840; permit $50–$340; gas plumbers $70–$190/hr
- Priciest area to work in: Downtown Riverside & the Eastside; lowest quotes: Ontario, Rancho Cucamonga & Pomona
Prices verified November 2026 · Cross-referenced against 35+ American pricing sources · See methodology
Installed prices include pipe, fittings, labor and a pressure test unless the row says otherwise. Riverside metro, re-verified November 2026. Per-foot rows are for the pipe run only.
| Service | Low | Typical | High |
|---|---|---|---|
| New gas line to one appliance (short run)per line | $280per line | $610 | $1,400 |
| Gas plumber hourly rate/hr | $70/hr | $105 | $190 |
| Service call feeper visit | $70per visit | $140 | $260 |
| Gas range or cooktop hookup (existing line)per job | $120per job | $210 | $420 |
| Gas wall oven hookup (existing line)per job | $140per job | $260 | $560 |
| Gas dryer hookup (existing line)per job | $95per job | $160 | $330 |
| Water heater gas connection (gas side only)per job | $120per job | $240 | $470 |
| Gas stub-out or quick-connect outlet (e.g. for a grill)per outlet | $240per outlet | $380 | $760 |
| Outdoor grill or fire pit gas lineper line | $380per line | $850 | $1,900 |
| Standby generator gas lineper line | $470per line | $1,150 | $2,850 |
| Garage or shop heater gas lineper line | $330per line | $760 | $1,700 |
| New gas line run, 50+ ftper line | $850per line | $1,700 | $3,800 |
| Black iron gas pipe, installedper foot | $14per foot | $21 | $33 |
| CSST flexible gas pipe, installedper foot | $10per foot | $16 | $24 |
| Underground polyethylene gas line with trenchingper foot | $19per foot | $28 | $47 |
| Vented gas fireplace insert or wall heater, installedinstalled | $1,450installed | $2,900 | $5,350 |
| Gas leak detection and repairper job | $140per job | $380 | $840 |
| Gas pressure test and inspectionper job | $70per job | $140 | $380 |
| Gas shutoff valve replacementper valve | $140per valve | $280 | $610 |
| Seismic gas shutoff valve (California and quake zones)installed | $240installed | $480 | $950 |
| CSST bonding to the electrical groundper home | $95per home | $190 | $380 |
| Propane to natural gas conversion (2–3 appliances)per home | $660per home | $1,700 | $3,800 |
| Gas meter relocation (utility + plumber)per job | $950per job | $2,400 | $4,300 |
| Gas piping permitper job | $50per job | $150 | $340 |
Got it as a PDF or photo? Upload up to 3 quotes and compare →
Get free quotes from up to 2 local gas line plumbers in Riverside
Free · No obligation · About a minute
- 1The job
- 2Budget
- 3Your details
What do you need a price on?
Tap one to start.
What's your rough budget?
A ballpark is fine. It helps the gas line plumbers who reply.
Where should they text you?
- Max 2 gas line plumbers. No call floods.
- 100% free. No obligation.
- 🔒 Only your matched gas line plumbers see your number.
By continuing, you agree to our Terms and to up to 2 gas line plumbers contacting you by phone or text.
Check your phone
Prices verified November 2026 · Cross-referenced against 35+ American pricing sources · See methodology
Figures are for the Riverside metro area. Trip fees can apply on the far edges; tight older homes in Downtown Riverside & the Eastside cost the most to work in.
Gas line prices across Riverside
Where you live in the metro changes the labor, not the pipe. Older homes in Downtown Riverside & the Eastside take the longest; jobs in Ontario, Rancho Cucamonga & Pomona tend to come in at or under the city typical.
Downtown Riverside & the Eastside
- Per line
- $300–$1,550 per line
- Typical job
- $410–$2,150 / grill or fire pit line
The priciest part of the metro for gas work: tight basements, old steel pipe, street parking and building rules all add time. Ask whether patching and the permit are in the price.
San Bernardino & Rialto
- Per line
- $290–$1,500 per line
- Typical job
- $390–$2,000 / grill or fire pit line
Renovated older homes next to new builds. A kitchen remodel that moves the range is the most common job here, and it's usually a short CSST or black iron run.
Moreno Valley & Perris
- Per line
- $280–$1,400 per line
- Typical job
- $380–$1,900 / grill or fire pit line
Mostly houses where the gas pipe is easy to reach under the floor or in the attic, so a new branch to an appliance is quick. Quotes cluster around the city typical.
Ontario, Rancho Cucamonga & Pomona
- Per line
- $280–$1,450 per line
- Typical job
- $380–$2,000 / grill or fire pit line
Newer homes, often with CSST already in place, so adding a branch is quick. Yard lines to a grill or generator are the big-ticket jobs.
Real-World Gas Line Costs in Riverside
Here's what common gas line jobs cost in Riverside in 2026, installed by a licensed pro with fittings and a pressure test.
Range hookup to an existing gas valve — 1–2 hours
Disconnect the old range, fit a new flexible connector, check the shutoff valve, connect, leak-test and light the burners. If there's no gas valve behind the range, it becomes a new-line job at $400–$1,820 with the hookup.
New line to a gas dryer, 15–25 ft — 2–4 hours
A branch off the nearest gas pipe, a shutoff valve, a sediment trap, the hookup and a pressure test. Add $130–$570 if the dryer also needs a new vent to the outside.
Grill or fire pit line across the yard — half a day to a day
Usually buried polyethylene ($19–$47 a foot with trenching), metal risers at each end, a shutoff and a quick-connect at the grill. Concrete or pavers in the way add patching at $95–$380.
Standby generator line — half a day to a day
Generators burn a lot of gas, so the line is usually bigger than a normal branch, and the utility may need to upgrade the meter. Ask whether that fee is in the quote. The permit runs $50–$340.
Gas smell at the range — find and fix the leak
A loose fitting or old connector behind the appliance is the cheap end. A leak inside a wall costs more, and a buried leak with digging costs the most. A service call alone is $70–$260.
How much does gas line installation cost in Riverside?
A short gas line in Riverside costs $280 to $1,400. The middle of the market, about $610, buys roughly 10–30 feet of new pipe, a shutoff valve, the hookup fittings and a pressure test by a licensed pro. Access, distance and pipe type push quotes up or down.
Leaks are priced differently: finding and fixing one runs $140–$840, more if the pipe is buried. Re-checked against 35 sources in November 2026.
Gas line prices in Riverside (2026): new lines, hookups and repairs
A short new line to one appliance costs $280–$1,400, a 50+ ft run $850–$3,800, and a standby generator line $470–$2,850.
| Line on the quote | Low | Typical | High |
|---|---|---|---|
| New gas line to one appliance (short run) | $280 | $610 | $1,400 |
| Gas range or cooktop hookup (existing line) | $120 | $210 | $420 |
| Gas dryer hookup (existing line) | $95 | $160 | $330 |
| Outdoor grill or fire pit gas line | $380 | $850 | $1,900 |
| Standby generator gas line | $470 | $1,150 | $2,850 |
| New gas line run, 50+ ft | $850 | $1,700 | $3,800 |
| Gas leak detection and repair | $140 | $380 | $840 |
| Gas meter relocation (utility + plumber) | $950 | $2,400 | $4,300 |
The pipe is the cheap part. On a typical $610 job in Riverside, most of the bill is a licensed plumber's time, fittings, the shutoff valve and the pressure test. That's why a 10-foot line and a 25-foot line are often priced close together.
What moves a gas line quote in Riverside:
- Distance — every extra foot of black iron adds about $21 installed; CSST about $16.
- Access — open basements and crawlspaces are quick; finished walls, slabs and attics take longer.
- Indoor vs outdoor — buried yard lines run $19–$47 a foot with trenching.
- Gas load — a generator or tankless heater can need bigger pipe and a utility meter check.
- Permit and test — $50–$340 for the permit; the pressure test should be in the price.
Ask every Riverside gas plumber for the same five things: the pipe type and length, what's included (valve, hookup, test, permit), any wall or yard patching, the labor warranty, and the start date. Compare those, not the headline price. Get a quote for your gas line work →
Gas Line Cost in Riverside by Number of Appliances
One appliance on a short run: $280–$1,400. Two or three appliances: $1,150–$2,850. Gas piping for a whole house with four or more appliances: $2,100–$7,100.
Worked example: a Riverside kitchen remodel that moves a gas range 12 feet and adds a gas dryer in the garage is two short runs in one visit. Expect about $820 for the new range line and hookup plus $160 for the dryer hookup on a shared branch, plus a $150 permit — about $1,130 all in, not two full jobs.
Adding a standby generator to that job brings in a bigger pipe and often a meter check: about $1,150 for the generator line on top. Doing it in the same visit saves a second service fee and a second permit.
Riverside Gas Line Costs by Pipe and Job Type
| Pipe or job type | Cost | Best for |
|---|---|---|
| Black iron pipe | $14–$33/ft installed | Indoor runs in basements and exposed spots, and the main trunk line. Rigid, very durable, more labor to cut and thread. |
| CSST flexible gas pipe | $10–$24/ft installed | Snaking through walls, floors and attics with few fittings. Must be bonded to the home's electrical ground. |
| Copper tubing (where allowed) | $10–$20/ft installed | Some areas and utilities allow it for gas; many don't. Ask your plumber and inspector before choosing it. |
| Underground polyethylene (PE) | $19–$47/ft installed | Buried yard lines to a grill, pool heater, generator or detached garage. Outdoor and underground only, with a tracer wire. |
| Short run to one appliance (10–30 ft) | $280–$1,400 per line | A new range, dryer, water heater or fireplace near existing gas pipe. |
| Long run, 50+ ft | $850–$3,800 per line | Across the house, up to an attic furnace or out to a detached garage. |
| Outdoor grill or fire pit line | $380–$1,900 per line | Patios and outdoor kitchens. Often a buried PE run with a riser and shutoff. |
| Standby generator line | $470–$2,850 per line | Whole-home backup power. Needs bigger pipe and sometimes a utility meter upgrade. |
| Flexible appliance connector | $95–$330 per hookup | The last few feet from the shutoff valve to a range, dryer or water heater, fitted as part of the hookup. |
Per-foot price vs what you actually pay — the Riverside gas line bill
Black iron costs $14–$33 a foot installed in Riverside, but short jobs don't price by the foot. Most plumbers charge a minimum that covers the trip, fittings, a shutoff valve and the pressure test, which is why a 10–30 ft line still lands at $280–$1,400.
Per-foot pricing matters on long runs. A 50+ ft line costs $850–$3,800, and a buried yard line $19–$47 a foot with trenching. On top of that, budget $50–$340 for the permit and any patching of walls or concrete.
What's included in a Riverside gas line quote (and what costs extra)
A standard installed price covers the new pipe and fittings, a licensed plumber's labor, a shutoff valve at the appliance, a sediment trap where needed, and a pressure and leak test before the gas goes on. The headline price often leaves out:
- Permit and inspection — $50–$340, required for new gas piping in most of the US
- The appliance hookup — $120–$420 for a range, if the quote only covers the line
- Wall, floor or yard patching — drywall repair can add up to $520; a small concrete patch $95–$380
- Meter or utility work — a meter move is $950–$4,300; some generator jobs need a utility meter upgrade
Ask whether the pressure test and the permit are in the price; a pro who skips either is cutting a corner that matters.
How far the line runs
Distance is the biggest driver after the minimum charge. A short run is $280–$1,400 in Riverside; a 50+ ft run $850–$3,800. Putting a new appliance close to existing gas pipe is the easiest saving.
Black iron or CSST
Black iron runs $14–$33 a foot installed and CSST flexible pipe $10–$24. CSST needs fewer fittings through walls but has to be bonded to the electrical ground ($95–$380 if it isn't already).
Basements, crawlspaces and finished walls
An open basement or crawlspace makes a new branch quick. Slab homes, finished ceilings and walls mean drilling, fishing pipe and patching afterward, which adds hours.
Local rules and conditions
Automatic seismic gas shutoff valves ($240–$950 installed) are a common add-on in California, and some cities require one with bigger remodels or a sale. Ask your building department, and use a valve on the state's approved list.
Permit and pressure test
New gas piping is pressure-tested before the gas goes on, and most cities inspect it. In Riverside budget $50–$340 for the permit; a separate test and inspection visit is $70–$380.
Gas load and pipe size
Every appliance adds to the gas the pipe has to carry. Adding a generator ($470–$2,850) or a tankless water heater can mean bigger pipe from the meter, and sometimes a utility meter upgrade.
Planned vs emergency
A booked job costs $280–$1,400 for a short run; a leak call starts with a $70–$260 service fee, and after-hours work costs more. If you smell gas, leave first and call the utility from outside.
- Bundle the jobs.One visit, one permit and one pressure test can cover a range, a dryer and a grill line. Each extra trip adds a service fee of $70–$260.
- Put appliances near existing pipe.Every foot counts on longer runs: about $21 a foot for black iron and $16 for CSST installed in Riverside.
- Ask about CSST for runs through finished walls.Flexible pipe needs fewer openings and fittings than threaded iron. Make sure the quote includes bonding to the electrical ground.
- Get an itemized quote.The permit ($50–$340), the pressure test and any patching should be on the quote, not a surprise on the invoice.
- Dig in the right season.Outdoor lines are cheapest when the ground is dry and unfrozen. Call 811 before anyone digs; it's free and marks buried utility lines.
- Get two quotes.Prices for the same short line in Riverside spread from $280 to $1,400. Two written quotes from licensed pros is the easiest way to land near $610.
Riverside gas plumbers often quote by phone. Before you pay a deposit, get these in writing:
- Pipe type and length, and the route it takes
- What the price includes: shutoff valve, sediment trap, hookup and connector
- Permit and inspection, and who pulls the permit
- Pressure test before the gas goes on
- Wall, ceiling or yard patching, and who does it
- CSST bonding to the electrical ground, if CSST is used
- For generators and big appliances: pipe size and whether the meter needs an upgrade
- Labor warranty, start date and payment terms
How much does it cost to run a gas line in Riverside?
$280–$1,400 for a short new line (about 10–30 ft) to one appliance, and $610 is typical. A 50+ ft run costs $850–$3,800.
How much does it cost to hook up a gas stove in Riverside?
$120–$420 if the gas valve is already behind the range. If you need a new line too, budget about $400–$1,820 for the line and the hookup together.
What does a gas dryer hookup cost in Riverside?
$95–$330 to connect a dryer to an existing gas valve. A new line to the laundry plus the hookup runs about $375–$1,730.
How much is a gas line to a grill or fire pit in Riverside?
$380–$1,900, usually a buried line with risers, a shutoff and a quick-connect. If gas pipe is already on the outside wall, a stub-out or quick-connect outlet is $240–$760.
What does a gas line for a standby generator cost in Riverside?
$470–$2,850 for the gas line alone. Generators need bigger pipe than most appliances, and some need a utility meter upgrade, so ask the gas company early.
How much does gas leak repair cost in Riverside?
$140–$840 to find and fix a typical leak, plus a service call of $70–$260 at many companies. Buried leaks that need digging cost more. If you smell gas, leave and call the gas utility or 911 from outside.
Do I need a permit for a gas line in Riverside?
In most cases, yes. New gas piping needs a licensed pro and usually a permit, a pressure test and an inspection. Budget $50–$340 for the permit; your plumber normally pulls it.
How much do gas plumbers charge per hour in Riverside?
$70–$190/hr, with about $105/hr typical. Many quote short jobs as a flat price instead, and some add a service call fee of $70–$260.
Is CSST or black iron cheaper in Riverside?
CSST usually costs less installed: $10–$24 a foot against $14–$33 for black iron, because it needs fewer fittings. CSST must be bonded to the home's electrical ground.
What's included in a Riverside gas line quote?
The pipe, fittings, a shutoff valve, labor and a pressure test. Often extra: the permit ($50–$340), the appliance hookup, and patching walls or concrete.
Prices verified November 2026 · Cross-referenced against 35+ American pricing sources · See methodology
Prices for the Riverside metro area, November 2026. Outer suburbs may vary.
Get a fair gas line quote in Riverside
Local gas line plumbers · Free quotes · No obligation, no spam.