Skip to content
Independent United States Cost GuidesPrices verified November 2026 · 39 trades · 195 US cities · 221+ sources For pros →
Get a fair quote

Cost guides

Plumbing & water4 trades
Electrical & energy5 trades
Renovation8 trades
Structural7 trades
Outdoor & yard7 trades
Cleaning & maintenance8 trades

More

Get a fair quote
Cost guide

How much does a carpenter cost in Reno?

By Our research team · Last verified · Methodology

Updated November 2026Independently researched11 min read
Carpenter cost

Carpenter costs in Reno

Get free quotesFree · no obligation · max 2 pros
Normal range for Reno, NV
$45–$125per hour

Most carpenters in Reno charge $45–$125/hr and $75/hr is what most homeowners pay. Finish carpenters bill $60–$160/hr; a reach-in closet build-out costs $895–$3,800.

How we get this data
Typical
$75/hr
Low end
$30/hr
High end
$200/hr
Hourly rate
$45–$125
Day rate (8 hrs)
$360–$1,000
Hang a pre-hung door
$150–$545
Baseboard, per ft
$4–$12

Want an exact price for your job?

Tell us the job. Casey checks it by text, then up to 2 local carpenters send you a real quote. Free, no obligation.

Get my fair quote →
Typical carpenter price: Reno vs nearby citiesTypical price, per hour. The line marks the US typical.
Oakland, CA $100/hr
Modesto, CA $85/hr
Stockton, CA $80/hr
Reno, NVThis guide $75/hr

The typical Reno price is $75/hr, in line with the US typical of $75/hr.

Where Reno sits among 195 US metrosNumber of metros at each typical carpenter price, per hour.

Reno's price band

Reno is pricier than 54% of the 195 US metros we price for carpenter work.

Expect $45–$125/hr for a carpenter in Reno, with $75/hr the going rate. Finish work costs more per hour than framing: a trim carpenter bills $60–$160/hr, a framer $40–$90/hr. By the job, crown molding is $7–$16 a foot and an exterior entry door $600–$2,500 installed.

Reno is a smaller market. A carpenter's hourly rate is pay plus the truck, tools, insurance and the hours nobody bills for, so it tracks local wages: carpenters in the Reno metro earn a median $62,350 a year, about 3% above the US median, and rates here run in line with the national typical of $75/hr.

Check your state contractor board for the dollar line above which a carpenter must hold a contractor license or registration, and ask your city building department whether the job needs a permit — framing, decks, stairs and structural repair usually do; trim, doors and closets usually do not. This is general information, not legal advice.

Comparing cities, or after the US-wide picture? See the national guide: Carpenter cost in the USA.

Quick answer

$45–$125/hr for a carpenter in Reno — typically $75/hr, or $360–$1,000 for a full day. Hanging a pre-hung door is $150–$545, baseboard $4–$12 a foot installed, and a reach-in closet build-out $895–$3,800. Verified November 2026. Get free Reno quotes →

  • Carpenter: $45–$125/hr ($75/hr typical); day rate $360–$1,000
  • Finish carpenter $60–$160/hr; framer $40–$90/hr; minimum $100–$395
  • Baseboard $4–$12/ft; crown molding $7–$16/ft installed
  • Hang a pre-hung door $150–$545; exterior entry door $600–$2,500 installed
  • Reach-in closet $895–$3,800; built-ins $250–$995/linear ft; pergola $2,500–$7,950

Prices verified November 2026 · Cross-referenced against 24+ American pricing sources · See methodology

Detailed pricing — Carpenter cost in Reno 2026

Labor with fasteners and basic supplies included; rows marked installed include standard paint-grade material. Reno metro, re-verified November 2026. Painting new trim, permits and premium hardwood are extra.

ServiceLowTypicalHigh
Carpenter hourly rate (labor, standard hours)/hr$45/hr$75$125
Carpenter day rate (8 hours, one carpenter)per day$360per day$600$1,000
Baseboard, installed (labor and primed MDF or pine), per linear ftper linear ft$4per linear ft$7$12
Door and window casing, installed, per linear ftper linear ft$4per linear ft$7$12
Crown molding, installed, per linear ftper linear ft$7per linear ft$11$16
Wainscoting or board-and-batten, installed, per sq ft of wallper sq ft$10per sq ft$20$40
Hang a pre-hung interior door (labor only, your door)per door$150per door$295$545
Interior door, installed, mid-range pre-hung door includedper door$250per door$445$845
Exterior entry door, installed (steel or fiberglass door included)per door$600per door$1,300$2,500
Door repair or rehang (sticking, sagging, loose frame)per job$100per job$200$395
Wood window repair (sash, sill or rotted trim)per job$150per job$320$645
Framing, labor and lumber, per sq ft of floor area (walls, not roof)per sq ft$7per sq ft$12$20
Deck building labor, per sq ft (framing and decking, materials extra)per sq ft$8per sq ft$15$25
Deck repair (replace boards, a joist or a railing section)per job$300per job$895$2,500
Stair repair (squeaky or loose tread, baluster, newel)per job$150per job$395$1,250
Stair handrail or railing, installed, per linear ftper linear ft$20per linear ft$40$90
Reach-in closet build-out (shelves, rods and drawers, installed)per closet$895per closet$1,800$3,800
Walk-in closet system, installedper closet$2,500per closet$4,950$9,950
Closet doors (bifold or bypass), replacedper opening$200per opening$400$845
Extra drawer unit in a closet or built-inper drawer$100per drawer$175$250
Custom built-ins (bookcase, entertainment wall), installed, per linear ftper linear ft$250per linear ft$495$995
Shelving installation (floating or wall shelves, a few)per job$150per job$345$795
Rot or structural repair (sill plate, rim joist, fascia or post)per job$500per job$1,500$3,950
Pergola, 10 × 12 ft wood, built on siteper pergola$2,500per pergola$4,450$7,950
carpenter jobs in Reno: what they costPer job, low to high with the typical price marked. Every line is in the table above.
Rot or structural repair (sill plate, rim joist, fascia or post) $1,500$500–$3,950
Deck repair (replace boards, a joist or a railing section) $895$300–$2,500
Stair repair (squeaky or loose tread, baluster, newel) $395$150–$1,250
Shelving installation (floating or wall shelves, a few) $345$150–$795
Wood window repair (sash, sill or rotted trim) $320$150–$645
Door repair or rehang (sticking, sagging, loose frame) $200$100–$395
Already got a quote?
Check it against these Reno prices — free, no sign-up.
$

Got it as a PDF or photo? Upload up to 3 quotes and compare →

Free quotes

Get free quotes from up to 2 local carpenters in Reno

Free · No obligation · About a minute

  1. 1The job
  2. 2Budget
  3. 3Your details
Casey · LocalGoingRate

What do you need a carpenter for?

Tap one to start.

Prices verified November 2026 · Cross-referenced against 24+ American pricing sources · See methodology

Figures are for the Reno metro area. Trip charges can apply on the far edges; parking and old, out-of-square buildings in Downtown, Midtown & the Riverwalk cost the most.

How carpenter costs vary across Reno

Carpenter rates across Reno

Same trade, four price bands. Parking, stairs and out-of-square old walls push Downtown, Midtown & the Riverwalk to the top, and rates in South Reno & Carson City sit near the city typical, with bigger jobs.

Carpenter prices across RenoTypical range by part of the metro, per hour. The line marks the Reno typical.
Downtown, Midtown & the Riverwalk8–12% above the city average $50–$140
East Reno & Wells AvenueStandard to 6% above $45–$135
SparksStandard pricing $45–$125
South Reno & Carson CityStandard; bigger jobs, more driving $45–$130

Downtown, Midtown & the Riverwalk

8–12% above the city average
Downtown, Midtown, Riverwalk District
Hourly
$50–$140/hr
Day rate
$390–$1,100 / day rate

Older buildings, plaster walls and paid parking. Building managers often want insurance papers and set work hours, and carrying lumber and a miter saw up stairs adds time to every job.

East Reno & Wells Avenue

Standard to 6% above
East Reno, Wells Ave, Northeast
Hourly
$45–$135/hr
Day rate
$370–$1,050 / day rate

A remodel-heavy area with older houses. Out-of-level floors, old plaster and surprise rot are common, so ask how surprises are priced before work starts.

Sparks

Standard pricing
Sparks, Spanish Springs, Victorian Square
Hourly
$45–$125/hr
Day rate
$360–$1,000 / day rate

Residential streets with average pricing. Bundling several small jobs into one visit is the easiest way to save here.

South Reno & Carson City

Standard; bigger jobs, more driving
South Reno, Damonte Ranch, Carson City
Hourly
$45–$130/hr
Day rate
$360–$1,050 / day rate

Mostly newer drywall homes with standard-size doors and openings, which keeps jobs quick. Expect average rates plus more square feet per job.

What you'll actually pay — job by job

Real-world carpentry costs in Reno

Here's what common carpenter jobs cost in Reno in 2026, labor, fasteners and basic supplies included.

One quick fix — a sticking or sagging door

$100–$395

Planing an edge, shimming a hinge or resetting a strike plate takes under an hour, but most Reno carpenters charge a minimum of $100–$395. Priced as a flat job it is $100–$395. Add a second small job to the same visit and the minimum stops hurting.

Trim out a 12 × 12 bedroom — baseboard, crown, one door and one window

$705–$1,765

About 45 ft of baseboard ($180–$540), 48 ft of crown ($335–$770), casing on the door ($70–$205) and the window ($120–$250) comes to $705–$1,765 in Reno, with primed MDF or pine. Filling, caulking and painting the trim is usually a separate line or a painter's job.

Replace three interior doors and fix a fourth

$850–$2,930

Three mid-range pre-hung doors installed at $445 each plus one repair at $200 is about $1,535. If the old doors are odd sizes — common in homes built before 1950 — the carpenter may have to trim or build out jambs, which pushes each door toward $845.

Reach-in closet build-out with two extra drawers

$1,095–$4,300

Shelves, a double hanging rod and a shoe rack in a standard 6–8 ft reach-in run $895–$3,800 in Reno; two drawer units add $175 each, for about $2,150. A walk-in closet system is $2,500–$9,950.

Rotted rim joist and a deck repair

$800–$6,450

Cutting out a rotted sill or rim joist and sistering new lumber is $500–$3,950 depending on how far the rot runs; replacing a few deck boards and a railing section is $300–$2,500. Together about $2,395. Anything load-bearing may need a permit in Reno, and the carpenter should say so before starting.

How much does a carpenter cost in Reno?

Between $45 and $125 an hour, with most Reno homeowners paying about $75. The spread is skill and the job: a framing carpenter bills $40–$90/hr and works fast; a finish carpenter bills $60–$160/hr and makes every joint invisible; a master carpenter $80–$200/hr.

By the job, Reno carpenters charge $150–$545 to hang a pre-hung door, $4–$12 a foot for baseboard and $7–$16 a foot for crown molding, so trimming out a 12 × 12 bedroom runs $705–$1,765. Figures re-checked against 24 sources in November 2026.

Carpenter rates and fees in Reno (2026)

Standard rates run $45–$125/hr, a full day $360–$1,000, and the minimum charge for a small job $100–$395.

Line on the quoteLowTypicalHigh
Standard hourly rate (general carpenter)$45$75$125
Finish or trim carpenter, hourly$60$95$160
Framing carpenter, hourly$40$60$90
Master carpenter, hourly$80$120$200
Minimum charge for a small job$100$200$395
Service call (1–1.5 hours of the rate)$45$95$190
Half day (4 × the hourly rate)$180$300$500
Full day (8 × the hourly rate)$360$600$1,000

The hourly rate is the small part. A finish carpenter at $95/hr who cuts clean miters once costs less than a cheaper one at $60/hr whose joints need filling, caulking and a repaint.

What moves a carpentry quote in Reno:

  • Finish or rough — framing bills $40–$90/hr and is priced per square foot; finish work bills $60–$160/hr because every joint shows.
  • The minimum — most carpenters charge $100–$395 for any visit, so a 30-minute door fix costs far more per minute than a day of trim.
  • Materials — paint-grade MDF or finger-joint pine is the cheap case; stain-grade oak, poplar or hardwood trim can double the material line, plus a 10–20% markup if the carpenter buys it.
  • The age of the house — out-of-square openings, plaster walls and odd-size doors in East Reno & Wells Avenue add hours; new construction in South Reno & Carson City goes fast.
  • Permits — trim, doors and closets need none; framing, load-bearing changes, decks and stairs usually do, and the permit plus any structural drawings add $50–$500 and up.

Ask every Reno carpenter the same five things: hourly or flat, the minimum charge, who buys the lumber and at what markup, whether filling, caulking and painting are included, and who pulls the permit if one is needed. Get a quote for your carpentry job →

Carpenter cost in Reno by job size

Quick answer

One small fix is $100–$395 (the minimum charge), a half day $180–$500, a full day $360–$1,000. A whole-room trim package is $705–$1,765, a reach-in closet $895–$3,800, a pergola $2,500–$7,950.

Worked example: trimming out a 12 × 12 bedroom in Reno. About 45 ft of baseboard at $7 a foot ($315), 48 ft of crown at $11 ($530), casing on one door ($120) and one window ($175) comes to about $1,140 with primed material, before paint.

A bigger job: framing the walls of a 12 × 12 room at $12 a square foot with lumber is about $1,750, and a 10 × 12 wood pergola is $4,450 typical. The pergola costs more per hour of work because the lumber, hardware and footings are in the price; framing is mostly labor.

Who to hire in Reno and what each carpenter costs

Who to hireCostBest for
General carpenter (journeyman)$50–$100/hrDoors, trim, decks, repairs and most everyday jobs. The rate most homeowners see.
Finish or trim carpenter$60–$160/hrBaseboard, casing, crown molding, wainscoting and stairs where the joints show. Slower and neater than a framer.
Framing (rough) carpenter$40–$90/hrWalls, floors, decks and additions, usually priced per square foot ($7–$20) rather than by the hour.
Cabinetmaker or built-ins specialist$75–$125/hrCustom bookcases, entertainment walls and closets, usually quoted per linear foot ($250–$995).
Master carpenter$80–$200/hrComplex stairs, curved work, historic trim profiles and jobs where nothing is standard.
Apprentice or helper$35–$55/hrBilled alongside a lead carpenter on bigger jobs. A two-person framing crew runs $80–$150/hr.
Handyman doing carpentry$45–$100/hrRehanging a door, a few feet of baseboard, a loose railing. Not for structural work or anything that needs a permit.
Day rate (8 hours, one carpenter)$360–$1,000 per dayA list of small jobs, a trim package or a two-day build. Cheaper than several separate visits.
Cost by who to hire in RenoTypical range, per hour.
General carpenter (journeyman) $50–$100
Finish or trim carpenter $60–$160
Framing (rough) carpenter $40–$90
Cabinetmaker or built-ins specialist $75–$125
Master carpenter $80–$200
Apprentice or helper $35–$55
Handyman doing carpentry $45–$100
Reno tip: once your list has four or five jobs on it, ask for a day rate ($360–$1,000) instead of separate flat prices.

Hourly rate vs what you actually pay — the Reno carpentry bill

A $75/hr rate rarely shows up as $75 on the invoice. Most Reno carpenters charge a $100–$395 minimum, so fixing one door costs $100–$395 as a flat job. Trim is priced by the foot — $4–$12 for baseboard, $7–$16 for crown — and the per-foot price already includes the material, the cuts, the nailing and the drive, which is why it works out to more than the hourly rate alone.

Compare flat prices, not hourly headlines. Two quotes for a 12 × 12 bedroom's trim ($705–$1,765 here) can differ by a third depending on whether one includes the material, the filling and caulking, and hauling the old trim away. Ask what is in each line before you compare the totals.

What's included in a Reno carpenter's quote (and what costs extra)

A standard carpentry quote covers labor, fasteners, glue and shims, cutting and fitting, and cleanup of the work area. Often left out:

  • Materials — lumber, trim, doors and hardware, plus a 10–20% markup if the carpenter buys them
  • Filling, caulking and painting — new trim usually arrives primed; painting it is $1–$4 a foot extra or a painter's job
  • Service call and the minimum — a service call is billed as $45–$190; $100–$395 minimum on a short visit
  • Permits and drawings — $50–$500 for a permit on framing, decks or stairs; $250–$1,000 for structural drawings on a load-bearing change

Ask for the price in writing before work starts, and for proof of liability insurance.

What affects carpenter costs in Reno

Finish or rough work

Framing carpenters in Reno bill $40–$90/hr, or $7–$20 a square foot with lumber. Finish carpenters bill $60–$160/hr because trim, stairs and built-ins show every cut.

Minimums and travel

Most carpenters charge a $100–$395 minimum, and a service call is billed as $45–$190 — one to one and a half hours of the rate — before the work starts.

Materials and markup

Primed MDF baseboard costs a few dollars a foot; stain-grade hardwood several times that. If the carpenter buys the lumber, expect the receipt plus a 10–20% markup. An interior door itself runs $30–$350 at the home center before labor.

Who does the work

A handyman doing light carpentry bills $45–$100/hr; a journeyman carpenter $50–$100/hr; a master $80–$200/hr. Pay for the skill the job needs — a sagging door does not need a master, a curved stair does.

Licensing and permits

Check your state contractor board for the dollar line above which a carpenter must hold a contractor license or registration, and ask your city building department whether the job needs a permit — framing, decks, stairs and structural repair usually do; trim, doors and closets usually do not.

Labor rates in Reno

Carpenters in the Reno metro earn a median $62,350 a year in federal wage data, about 3% above the US median. An hourly rate is almost all labor, so Reno prices land in line with the US typical of $75/hr.

The age of the house

Homes built before 1950 rarely have square openings or standard door sizes, and plaster walls crack when trim is nailed. Expect more hours in East Reno & Wells Avenue and Downtown, Midtown & the Riverwalk; newer homes in South Reno & Carson City go faster.

How to save on a carpenter in Reno
  1. Batch small jobs into one visit.One $200 minimum can cover a door fix, a loose railing and a few feet of trim. Write a list before the carpenter arrives.
  2. Book a day rate for long lists.A full day in Reno is $360–$1,000. A trim package or four or five small jobs often costs less this way than flat prices one at a time.
  3. Choose paint-grade trim.Primed MDF or finger-joint pine baseboard costs a fraction of stain-grade oak and installs faster. Baseboard runs $4–$12 a foot installed here; hardwood can double the material line.
  4. Buy the doors and hardware yourself.An interior door costs $30–$350 at the home center. Supplying it skips the markup and the store run; labor to hang a pre-hung door is $150–$545.
  5. Get the finish line in writing.Ask whether filling nail holes, caulking and painting the trim are in the price. Many carpenters leave trim primed and unpainted, and a painter charges extra to finish it.
  6. Keep structural work permitted.Don't pay a carpenter to skip a permit on framing, a deck or a stair in Nevada. A failed inspection or an insurance denial costs more than the permit.
What a carpenter's quote in Reno should include

Reno carpenters quote by the hour, by the foot or by the job. Before you pay a deposit, get these in writing:

  • The carpenter's name, business name and proof of liability insurance
  • Hourly rate plus the minimum charge, or a flat price per job
  • Each job on its own line — doors, trim per foot, closets, repairs
  • Materials: species and grade (paint-grade MDF, pine, poplar, oak), who buys them and at what markup
  • Whether filling, caulking and painting the trim are included
  • Removal and disposal of old trim, doors or rotted lumber
  • Whether the job needs a permit, and who pulls it
  • Start and finish dates, payment stages and the warranty on the work
Frequently asked questions — Carpenter cost in Reno
How much does a carpenter cost per hour in Reno?

$45–$125/hr, and $75/hr is typical. Framers bill $40–$90/hr, finish carpenters $60–$160/hr, and most charge a $100–$395 minimum.

What is a carpenter's day rate in Reno?

About $360–$1,000 for 8 hours, before materials. It is the cheapest way to clear a list of small jobs or a trim package; a single service call is billed as $45–$190.

How much does it cost to install baseboard or crown molding in Reno?

Baseboard is $4–$12 a linear foot installed with primed material, crown molding $7–$16. A 12 × 12 room's baseboard runs $180–$540; its crown $335–$770.

How much does it cost to hang a door in Reno?

$150–$545 labor to hang a pre-hung interior door you supply, or $250–$845 with a mid-range door included. An exterior entry door installed is $600–$2,500.

How much is framing per square foot in Reno?

$7–$20 per square foot of floor area with lumber, for walls. Framing a 12 × 12 room is about $1,000–$2,900; a single interior wall with drywall $995–$4,950.

How much do custom closets and built-ins cost in Reno?

A reach-in closet build-out is $895–$3,800, a walk-in system $2,500–$9,950, and custom built-ins $250–$995 per linear foot installed.

Do I need a licensed carpenter in Nevada?

Check your state contractor board for the dollar line above which a carpenter must hold a contractor license or registration, and ask your city building department whether the job needs a permit — framing, decks, stairs and structural repair usually do; trim, doors and closets usually do not.

Do I need a permit for carpentry work?

Not for trim, doors, closets, shelving or like-for-like repairs. Framing, moving or removing a wall, new window or door openings, decks over a small size, stairs and structural rot repair usually need a building permit, and a load-bearing change may need drawings from a licensed structural engineer. Ask the carpenter who pulls it. This is general information, not legal advice.

Is it cheaper to pay a carpenter by the hour or by the job?

For one clear job — a door, a run of trim, a closet — a flat price is usually cheaper and safer. For a long list, a day rate ($360–$1,000) costs less than paying $100–$395 minimums one visit at a time.

Does a carpenter supply the lumber and doors?

Most will, at cost plus a 10–20% markup, and some charge for the trip. You can save by buying doors ($30–$350 each for the door itself) and hardware yourself; let the carpenter pick the trim stock so the profiles match.

Prices verified November 2026 · Cross-referenced against 24+ American pricing sources · See methodology

Prices for the Reno metro area, November 2026. Outer suburbs may vary.

Our methodology
These are independent estimates built from published cost guides, platform price data, dated city price pages, home-center material prices and federal wage data. No carpenter can pay to change them, so always get two or three quotes. Last reviewed November 2026. Read our full methodology →

Get a fair carpenter quote in Reno

Local carpenters · Free quotes · No obligation, no spam.

Get quotes in Reno →Max 2 carpenters will contact you
Get quotes in RenoMax 2 carpenters · free · no spam→